
Low block walls and pillars (murete) built to last
The base of most fences in Spain is a low block wall with pillars. We build that base properly, so whatever goes on top has something solid to stand on.
A low wall with pillars, known in Spain as a murete con pilares, is a short concrete block wall on a continuous footing with taller block pillars at intervals, designed either as a finished boundary in its own right or as the base for an infill such as slats, mesh or panels.
What is a murete with pillars?
In short: it is a low block wall on a continuous footing, with taller pillars at intervals, used as a boundary or as the base for an infill.
The murete is the backbone of the typical Spanish boundary. It lifts the infill above the ground, keeps garden soil and water away from slats or panels, and gives the boundary a solid line at the bottom. The pillars – usually block, sometimes split-face or rendered – carry the infill and break up long runs.
A murete can be finished in several ways: bare grey block to be rendered later, split-face block left exposed, or rendered and painted. The structure underneath is the same: a footing sized for the ground and the load, block courses, reinforcement where needed and pillars tied into the footing.
We often build the murete and pillars as a stage on their own, either because the owner will choose the infill later, or because the infill will be fitted by another trade. That is why this page exists separately from the page on a low wall with a fence on top.

Why do the pillars matter so much?
In short: the pillars take the wind load and the weight of the infill, so their position, reinforcement and connection to the footing decide how the whole fence behaves.
A low wall on its own carries little load. The moment you add a tall infill – slats, boards, mesh – wind pushes on it, and that force is transferred to the pillars and down into the footing. If the pillars are too far apart, poorly reinforced or not tied into the foundation, the problems show up later as cracks at the base of the pillars or leaning sections.
That is why we ask early what will go on top. The infill decides the spacing of the pillars, how fixings will be placed and whether a channel or plate needs to be set into the pillar. If you already have a supplier for the infill, we coordinate with their fixing requirements. The pillar spacing that suits one system may not suit another, so we never set it out by habit.
Pillars are also where most visual decisions are made: height above the wall, caps, split-face or render.

Which properties suit a murete with pillars?
In short: almost any residential plot: villas, townhouses with gardens, country houses near a road, and plots being prepared for a later infill.
This layout is popular because it balances privacy, cost and appearance. The murete deals with the ground and the pillars give structure; the infill can be chosen to match the level of privacy you want, from open mesh to closed slats.
It is especially useful when:
- you want a boundary now and will decide on the infill later;
- you have dogs and want a solid base along the bottom of the fence (we explain this, but the right infill height and type depends on your animals);
- your plot is on a gentle slope and the wall can be stepped while the infill stays level;
- your urbanisation limits the height of solid walls but allows an open infill above.
For a fully solid boundary see our split-face block wall and rendered block wall pages.
What needs checking first – rules and the boundary?
In short: confirm the boundary line, the height and solidity rules of your town and urbanisation, and whether the wall will hold back soil.
Local rules often treat the solid part of a boundary differently from the open part above it. That is why the height of the murete and the type of infill are not only design questions. The ayuntamiento sets the general rules; the urbanisation may add its own. Our permits guide explains how to check them.
The other early check is the ground. If the plot slopes, the murete may need to step down, and if there is a level difference across the line it may be holding earth back. A murete is not a retaining wall. Read the guide on walls on sloping plots and the foundations guide before you commit to a layout.
How do you maintain a murete and pillars?
In short: keep caps intact, keep water and soil off the base, and check the joints where infill is fixed into the pillars.
A murete needs the same care as any masonry wall: caps that shed water, a base that does not stay wet, and quick repair of cracks. The specific weak points are where the infill meets the pillars. Fixings drilled into masonry can let water in if they are not sealed, and movement of the infill in wind can work them loose over time.
If the murete is rendered, repaint as needed. If it is split-face, occasional cleaning is enough. Any crack at the base of a pillar deserves attention, because that is where wind loads concentrate; our guide on cracks in boundary walls explains what to look for.
What affects the cost of a murete with pillars?
In short: length, wall height, pillar height and number, footing, finish, ground and access, plus any removal work.
The cost of a murete is driven more by the groundwork and the pillars than by the low wall itself. A long run with few corners on flat ground is the simplest case; a short run with many pillars, steps and corners on sloping ground takes more labour per metre.
We list every stage separately in our quote, so if you later add an infill you can see what the base cost and what the infill adds. For a general guide to quotes see fence and wall quotes, and for the first decisions read first boundary wall options.
How we build it – step by step
- Agree the infill first
We ask what will go on top, because that decides pillar spacing, height and fixings.
- Setting out
We mark the wall line, pillar positions and any steps on the ground.
- Excavation
We dig the trench for a continuous footing and the pillar bases.
- Footing and reinforcement
We place reinforcement, leave starter bars for the pillars and pour the concrete.
- Low wall courses
We lay the murete courses in the chosen block, stepping them where the ground falls.
- Pillars
We raise the pillars, reinforced and filled where required, and set any fixing points for the infill.
- Caps and finish
We fit caps and render or point the wall as agreed.
- Clean-up and handover
We clear the site and hand over the base ready for the infill, with photos if you are away.
When is it the right choice – and when not?
A good fit if…
- A base for slats, composite, mesh or concrete panels
- Owners who will choose the infill later
- Plots on gentle slopes
- Properties with dogs that need a solid bottom line
- Urbanisations that limit solid wall height
Consider another option if…
- Holding back soil between two levels
- Owners who want only a light mesh fence on posts
- Sites where the infill system needs posts fixed directly into the ground
What affects the cost?
We don't publish fixed prices: every fence is quoted line by line using these factors.
- Length in linear metres
- Height of the murete
- Number and height of pillars
- Footing and ground conditions
- Steps along a slope
- Finish: bare block, split-face or render
- Access for materials
- Removal of an old fence
- Fixing points prepared for the infill
Articles and guides

Low block wall with a fence on top – one job, one contractor
Privacy above, a solid base below. We build the block wall and pillars and fit the infill, so there is one person responsible for the whole boundary.
View details →
Split-face block walls for villas and plots in Málaga
A textured block wall that needs no render or paint. We set it out, dig and pour the footing, lay the courses and finish the pillars and caps.
View details →Building block walls on sloping plots
Málaga's hills make level plots the exception. A wall on a slope can look neat and stay sound, as long as the steps, footings and levels are planned from the start.
View details →
Building your first boundary wall in Spain: the best options
New owners in Spain face unfamiliar terms, rules and trades. This guide sets out the main wall options in plain English and the order in which to decide.
View details →
Block wall foundations: what holds a boundary wall up
Most problems in boundary walls start below ground. This guide explains, without jargon, what a footing does and what a contractor should check before pouring one.
View details →Frequently asked questions
Can you build only the murete and pillars?
Yes. We often build the base on its own, either because the owner will choose the infill later or because it will be installed by someone else. We prepare the pillars to suit the infill you are planning.
How far apart should the pillars be?
There is no single answer. It depends on the infill, its weight, the wind exposure and the reinforcement. We set the spacing for your specific design rather than using a fixed rule.
Can an existing low wall be reused?
Sometimes. If the footing is adequate and the wall is sound, an infill can be added. If the wall was built for a light fence, adding a tall, closed infill may overload it.
Which infill can go on top?
Aluminium or steel slats, composite boards, mesh panels or precast concrete panels are all common. Each has its own sister site in our network if you want to look into them.
Do pillars need a cap?
We recommend it. A cap protects the top of the pillar from water and finishes it visually.
Can the murete follow a slope?
Yes, it can step down in sections. If the level difference across the line is significant, a technician may need to check whether the wall is retaining soil.
Can the pillars be split-face and the wall rendered?
Yes, mixing finishes is common. We agree the combination before ordering materials.
Do I need a permit for a low wall?
In most cases some form of municipal permission is required, but the route depends on the town and the land classification. Check with your ayuntamiento or read our permits guide.
Is a murete good for keeping dogs in?
A solid base stops digging along the line and gives the infill a firm bottom. The right overall height and infill depend on your dogs; the pillar design should allow for it.
Can you quote from photos?
Yes. Send photos and the approximate length and we can prepare a first assessment, which we confirm on site before work starts.
Planning a block wall? Send us photos
Send photos and the approximate length of your boundary. We reply with questions or a first itemised assessment, without commitment.