
Low block wall with a fence on top – one job, one contractor
Privacy above, a solid base below. We build the block wall and pillars and fit the infill, so there is one person responsible for the whole boundary.
A low wall with a fence on top is a boundary made of a short masonry wall (murete) with pillars, on which an infill of slats, boards, mesh or panels is fixed, combining the strength of a block base with a lighter, partly open upper section.
What is a low wall with a fence on top?
In short: it is a block murete with pillars and an infill fixed between or on top of them – the most common boundary layout on the Costa del Sol.
This is the layout you see along most residential streets in Málaga province: a low wall, usually rendered or split-face, with pillars at intervals and something lighter above – horizontal aluminium slats, composite boards, mesh panels or, sometimes, concrete panels.
The two parts do different jobs. The wall gives a solid line at ground level, keeps water and soil off the infill, and carries the look of the boundary. The infill sets the level of privacy and lets you choose between a closed screen and a more open view. Where in Spain people say valla sobre murete, this is what they mean.
The difference between a good and a mediocre result is usually in the connection between the two: how the pillars were prepared for the infill, whether fixings are aligned, whether the infill sits level while the wall steps with the ground.

Why build the wall and the infill as one job?
In short: because the wall has to be designed for the infill, and one contractor can be held responsible for how the two work together.
When the wall is built by one trade and the infill by another, problems tend to fall between them: pillar spacing that does not match standard panels, fixing points in the wrong place, pillars that are not quite plumb. Each side can say the other is responsible.
We build the whole fence – groundwork, wall, posts and panels. We set out the pillars for the chosen infill, prepare the fixing points, and fit the infill once the masonry has settled. If you prefer a particular infill product or supplier, we can work with it, or with material you supply, provided we know it before we build the pillars.
What we do not build: gates and automation are not part of our service. If your boundary needs a gate opening, we leave the opening and the pillars as agreed so that a gate specialist can fit it afterwards.

Which infill works best on a block wall?
In short: it depends on how much privacy you want, how exposed the plot is to wind, the look of the house and the urbanisation rules.
The main options we see are:
- Aluminium or steel slats – clean lines, many colours, from fully closed to partly open. Our sister site on aluminium fences on a wall goes into detail.
- Composite or timber boards – a warmer look, popular around gardens.
- Mesh panels – the most open option, for when the view matters more than privacy.
- Precast concrete panels – heavy and solid; see our page on the precast concrete panel fence.
The more closed the infill, the more wind it catches. A closed screen on a hill or near the sea puts more load on the pillars and footing than an open one. We take that into account in the design rather than leaving it to chance. Our article on block wall or metal fence compares the main approaches.

What do local rules usually say about walls with infill?
In short: many towns and urbanisations treat the solid part and the open part of a boundary differently, so check both before choosing heights.
Rules on boundary walls are set locally. The ayuntamiento decides through its planning documents and ordinances; the urbanisation may add rules about colours, materials and how open a street boundary must be. It is common for the height of the solid part to be limited separately from the total height, but the actual figures differ from place to place, so we do not quote them from memory.
Before ordering anything, check the rules that apply to your plot. Our permits guide explains the usual routes, and the network's general guide on fence height rules covers the wider picture.
How do you maintain a wall with a fence on top?
In short: look after the masonry as any wall, and check the fixings and the infill material according to its own care needs.
The masonry part needs little: intact caps, a dry base, repainting if it is rendered. The infill depends on the material: aluminium needs occasional washing, composite needs cleaning, timber needs treatment. The point to check on all of them is the fixing into the pillars. Look for loose screws, gaps where water can enter the masonry, and movement in strong wind.
If a pillar shows a crack at its base, do not ignore it. Our guide on cracks in boundary walls explains which patterns usually point to a structural issue.
What affects the cost of a wall with infill?
In short: everything that affects the wall plus the infill material, its height, how closed it is and how it is fixed.
Because there are two systems, there are two groups of factors: those of the masonry base – length, height, footing, ground, access – and those of the infill – material, finish, height and fixings. Our itemised quote keeps them on separate lines so you can compare infill options on the same base.
For a full explanation of how fence quotes are put together, see fence and wall quotes. Our post on mistakes when choosing a block wall covers the decisions that most often lead to extra cost later.
How we build it – step by step
- Choose the infill
We agree the infill type and height, because it decides the whole design of the base.
- Setting out
We mark the line, pillar positions and any openings you want to leave.
- Excavation and footing
We dig and pour a reinforced footing to suit the ground and the expected load.
- Low wall and pillars
We build the murete and pillars, with fixing points prepared for the infill.
- Finish the masonry
We render or point the wall and fit the caps.
- Fit the infill
We install the slats, boards, mesh or panels level and aligned between the pillars.
- Final checks
We check fixings, alignment and finishes along the whole run.
- Clean-up and handover
We clear the site and send or show you the finished boundary.
When is it the right choice – and when not?
A good fit if…
- Street frontages that need privacy and a tidy look
- Owners who want one contractor for the whole boundary
- Plots where solid wall height is limited by local rules
- Gardens with dogs that need a solid base
- Owners managing works from abroad
Consider another option if…
- Boundaries that need a gate built by us (we do not build gates)
- Retaining soil between two levels
- Very long rural boundaries where a mesh fence on posts is more sensible
What affects the cost?
We don't publish fixed prices: every fence is quoted line by line using these factors.
- Length in linear metres
- Height of wall and of infill
- Infill material and how closed it is
- Number of pillars and corners
- Footing and ground conditions
- Wind exposure of the plot
- Slope and steps
- Access for materials
- Removal of an old fence
Articles and guides

Low block walls and pillars (murete) built to last
The base of most fences in Spain is a low block wall with pillars. We build that base properly, so whatever goes on top has something solid to stand on.
View details →
Rendered block boundary walls in Málaga province
The classic Andalusian boundary: a block wall finished with render and paint. We build the structure and apply the render so the wall matches the house.
View details →
Block wall or metal fence: which boundary suits your plot?
It is rarely a straight choice between a wall and a fence. This comparison explains what each does well, and why the most common answer on the coast is a mix of the two.
View details →Building block walls on sloping plots
Málaga's hills make level plots the exception. A wall on a slope can look neat and stay sound, as long as the steps, footings and levels are planned from the start.
View details →
Precast concrete panel fences (placas de hormigón)
A solid, heavy boundary built from factory-made concrete panels that slide into posts. We set out, pour the post footings and assemble the panels in line.
View details →Frequently asked questions
Do you fit the infill or only build the wall?
Both. We can build the whole boundary, or just the wall and pillars if you prefer another installer for the infill. We need to know the infill before we build the pillars.
Can I supply the slats or panels myself?
Yes, we work with material supplied by the client. Tell us the product in advance so the pillars are prepared for its fixings.
Which is more private: slats or a full wall?
A full wall blocks the view completely. Closed slats come close, with a lighter look and some airflow.
Do you build gates?
No. Gates and automation are not part of our service. We leave the opening and pillars ready for a gate specialist.
Is an open infill better on a windy plot?
Usually, yes. A more open infill lets wind through and puts less load on the pillars. We design the pillars and footing for the infill you choose.
Can the infill stay level on a sloping plot?
Often, yes. The wall can step with the ground while the infill sections are kept level or follow a stepped line. We agree it at setting out.
How do I know what height is allowed?
Check your town's rules and your urbanisation's rules. Our permits guide explains how to ask the ayuntamiento.
Can an existing wall take a new infill?
Only if the wall and its footing can carry it. Adding a tall closed screen to a wall built for a light fence is a common cause of cracks.
Is this layout good for dogs?
A solid base stops digging under the fence, and the infill can be chosen to stop jumping or seeing through. The right combination depends on your animals.
Can I follow progress from abroad?
Yes. We send photos at each stage: footing, wall, pillars, infill and the finished boundary.
Planning a block wall? Send us photos
Send photos and the approximate length of your boundary. We reply with questions or a first itemised assessment, without commitment.